On January 26, 2026, AAM – American Axle & Manufacturing Holdings, Inc.
changed its name to Dauch Corporation.
Learn more here.
-
Parts by Axle Type
-
GM Axle Types
- 10.5" 14 Bolt - Rear Axle
- 11.5" 14 Bolt - Rear Axle
- 12.0" 14 Bolt - Rear Axle
- 195 MM Rear Axle
- 218 MM Rear Axle
- 250 MM Rear Axle
- 7.25" IFS - Front Axle
- 7.6" 10 Bolt - Rear Axle
- 7.6" IFS - Front Axle
- 8.0" 10 Bolt - Front Axle
- 8.0" 10 Bolt - Rear Axle
- 8.25" IFS - Front Axle
- 8.6" 10 Bolt - Rear Axle
- 9.25" Clamshell - Front Axle
- 9.25" Salisbury - Front Axle
- 9.5" 12 Bolt - Rear Axle
- 9.5" 14 Bolt - Rear Axle
- 9.5" 8 Bolt RDM
- 9.76" 12 Bolt - Rear Axle
- 9.76" 8 Bolt RDM
- Chrysler Axle Types
- Ford Axle Types
-
GM Axle Types
-
Parts by Category
- Axle Components
- Driveshaft Components
-
Installation Parts and Kits
- ABS Tone Rings
- Adjusters and Retainers
- Collapsible Spacers
- Disconnect Shifter Components
- Electric Shift Actuators
- Bearings
- Nuts, Washers, and Bolts
- Seals and Gaskets
- Vents, Drain and Fill Plugs
- Ball Joint Kits
- Cover Pan Kits
- Differential Gear Kits
- Disconnect Shifter Kits
- Master Bearing Kits
- Master Install Kits
- Output Shaft Seal Kits
- Pinion Seal Kits
- Wheel End Kits
- Wheel Joint Kits
- Steering Components
-
Exploded Views By Axle Type
-
GM Axle Types
- 7.25 FrontAxle IFS Clamshell
- 7.25 FrontAxle IOP Clamshell
- 7.6 FrontAxle IFS Salisbury
- 7.6 RearAxle Salisbury 10Bolt
- 8.0 FrontAxle Salisbury 10Bolt
- 8.0 RearAxle Salisbury 10Bolt
- 8.25 FrontAxle IFS Clamshell
- 8.6 RearAxle Salisbury 10Bolt
- 9.25 FrontAxle IFS Clamshell
- 9.25 FrontAxle IFS Salisbury
- 9.5 RearAxle Salisbury 12Bolt
- 9.5 RearAxle Salisbury 14Bolt
- 9.5 RDM 8Bolt
- 9.76 RDM 8Bolt
- 9.76 RearAxle Salisbury 12Bolt
- 10.5 RearAxle Salisbury 14Bolt
- 11.5 RearAxle Salisbury 14Bolt
- 12.0 RearAxle Salisbury 14Bolt
- Chrysler Axle Types
-
GM Axle Types
- Where To Buy
- Technical Support
- About AAM
- Latest News
- Contact AAM
- Cart (0)
- Dealer Log In
Technical Support
To determine the ring gear diameter you need to measure the outside diameter of the ring gear.
